|Chainette Fringe||Beaded Fringe||Beaded Garland||Feather Fringe||$ale|
Wedding & Event Ideas
Flooring - What is Coefficient of Friction?
Shop all our Fabulous Finds
Artwork & Accessories
Cabinets & Countertops
Careers In Interior Design
Color Trends & Color Schemes
Decorating & Home Decor Trends
Education In Interior Design
Fabrics & Upholstery
Floors & Flooring
Home Health & Safety
Interior Designers, Working With
Painting & Home Decor
Walls & Doors
Shipping & Return Info
Our beaded fringe trims are 1st quality and exceptional in craftsmanship and detail.
Article courtesy of The Marble Institute of America
Stone used on commercial and residential floors should provide a safe walking surface in both wet and dry conditions. By measuring the coefficient of friction (COF), a quantitative number can be used to express the degree of slip resistance of a floor surface.
When the coefficient of friction is measured from a resting position, it is called the "static coefficient of friction" (SCOF). When it is measured when the surfaces are in relative motion, it is called the "dynamic coefficient of friction". Measuring the dynamic COF is difficult and requires a strict laboratory environment for accurate results. Almost all portable and laboratory meters measure only the static COF and most measuring devices (slip meters) refer to static COF. The higher the SCOF, the less slippery the surface. It is possible to have too high a SCOF; the surface can be too slip resistant and difficult to walk on.How is the coefficient of friction measured? There are two types of machines that can measure static COF &endash; permanent laboratory models and portable field models that are commonly referred to as pull meters. The most common method of measuring slip resistance uses a 50-pound weight placed flat on a Neolite shoe heel which is then placed flat on the stone surface being tested. The heel and weight assembly are pulled across the stone with a spring or electronic scale. The maximum amount of force (pounds) needed to start the assembly in motion is recorded. This measurement is divided by the weight (50 pounds) and yields the coefficient of friction value.
Tests to measure slip resistance were developed primarily for man-made materials, with the earliest from the 1940s when Sidney James conducted experiments to rate floor polishes and other floor maintenance chemicals for Underwriters Laboratories. From these experiments came the James Machine (ASTM D-2047) and the 0.5 static coefficient of friction as the threshold of safety for normal ambulation. Unlike other test methods, the James Machine can only be used in a laboratory for testing smooth, dry surfaces and test results cannot be compared to those of other test methods.
ASTM Tests The American Society for Testing and Materials (ASTM) currently recognizes several standard methods for measuring coefficient of friction depending on the application. C-1028-96- (Standard Test Method for Determining the Static Coefficient of Friction of Ceramic Tile and Other Like Surfaces by the Horizontal Dynamometer Pull-Meter Method) This is the most common test used to measure slip resistance in the field and uses a portable horizontal pull meter. This test method may be used under both wet and dry conditions and uses Neolite heel assemblies. D-2047-93- (Standard Test Method for Static Coefficient of Friction of Polish-Coated Floor Surfaces as Measured by the James Machine) The James Machine is designed for measuring COF in the laboratory under strictly controlled conditions and cannot be used in the field. It is not suitable for use on wet, rough or corrugated surfaces; it can only be used to measure dry surfaces. The James Machine is considered by most authorities to be the most accurate and reliable measurement of slip-resistance. F-462-94- (Consumer Safety Specification for Slip-Resistant Bathing Facilities) This test covers the slip resistance of bathtubs and shower structures or combinations. It uses a device with a silicone rubber attached to an arm and is conducted in soapy water to evaluate the COF. F-609-96- (Standard Test Method for Using a Horizontal Pull Slipmeter [HPS]) In addition to C-1028 this test standard is the most widely accepted method for measuring slip resistance. It uses a horizontal pull slip meter to measure the static slip resistance of footwear sole, heel or related materials on walkway surfaces. F-1679-96-(Standard Test Method for Using a Variable Incidence Tribometer [VIT]) and F-1677-96- (Standard Test Method for Using a Portable Inclineable Articulated Strut Slip Tester [PIAST]) These standards measure the slip resistance of footwear sole, heel or related materials against planar walkway surfaces or walkway surrogates in either the laboratory or field under dry, wet or contaminated conditions. The two most common tests for measuring static coefficient of friction are C-1028 and D-2047. The methods and results of these two tests are very different and cannot be compared. D-2047 uses the James Machine in a controlled laboratory environment that measures on dry, smooth surfaces and cannot be used in the field on existing flooring surfaces. Because of the consistency of the testing method of the James Machine, it is considered to provide the most accurate and reliable measurement of SCOF for smooth, dry surfaces. C-1028 is a portable field test procedure that uses a horizontal pull meter. It can be used on wet or dry as well as smooth or textured flooring surfaces. Because of the environmental variables associated with tests using portable pull meters, the results are inconsistent from surface to surface and the reliability is low. There are portable slip meters on the market which claim to measure the static COF. When purchasing slip meters, be sure they comply with the ASTM requirements for the applicable test procedure. For further information on slip meters contact ASTM at 100 Barr Harbor Drive, West Conshohocken, PA 19428 or see their web site at www.astm.org. ADA Recommendations In 1990 The Americans with Disability Act was adopted and states that areas of public accommodation must comply with the provisions specified in the Americans with Disabilities Act Accessibility Guidelines (ADAAG). The ADA Handbook EEOC-BK-1 is available from the United States Government Printing Office. The following is from appendix B, A4.5 A4.5 Ground and Floor Surfaces. A4.5.1 General. People who have difficulty walking or maintaining balance or who use crutches, canes or walkers, and those with restricted gaits are particularly sensitive to slipping and tripping hazards. For such people, a stable and regular surface is necessary for safe walking, particularly on stairs. Wheelchairs can be propelled most easily on surfaces that are hard, stable, and regular. Soft loose surfaces such as shag carpet, loose sand or gravel, wet clay, and irregular surfaces such as cobblestones can significantly impede wheelchair movement. Slip resistance is based on the frictional force necessary to keep a shoe heel or crutch tip from slipping on a walking surface. While the dynamic coefficient of friction during walking varies in a complex and non -uniform way, the static coefficient of friction, which can be measured in several ways, provides a close approximation of the slip resistance of a surface. Contrary to popular belief, some slippage is necessary to walking, especially for persons with restricted gaits; a truly non-slip" surface could not be negotiated. The Occupational Safety and Health Administration recommends that walking surfaces have a static coefficient of friction of 0.5. A research project sponsored by the Architectural and Transportation Barriers Compliance Board (Access Board) conducted tests with persons with disabilities and concluded that a higher coefficient of friction was needed by such persons. A static coefficient of friction of 0.6 is recommended for accessible routes and 0.8 for ramps. It is recognized that the coefficient of friction varies considerably due to the presence of contaminants, water, floor finishes, and other factors not under the control of the designer or builder and not subject to design and construction guidelines and that compliance would be difficult to measure on the building site. Nevertheless, many common building materials suitable for flooring are now labeled with information on the static coefficient of friction. While it may not be possible to compare one product directly with another, or to guarantee a constant measure, builders and designers are encouraged to specify materials with appropriate values. As more products include information on slip resistance, improved uniformity in measurement and specification is likely. The Access Boards advisory guide lines on Slip Resistant Surfaces provides additional information on this subject. Commentary & Recommendations The ADA does not specify slip resistance standards or test methods of measurement, and refers only to an OSHA recommendation and an Access Board recommendation for the numerical values. The guidelines recognize that the static coefficient of friction is affected by floor finishes, surface coatings, contaminants, water and other environmental variables. It is partly for this reason that all recommended values are given for a dry state only. Slip resistance for natural stone is most commonly tested by ASTM C-1028, the test developed to measure the SCOF of ceramic tile. There is no test specifically designed to measure the SCOF of natural stone. ASTM C-1028, when used to test natural stone, yields differing results that are subject to the inherent variations in natural stone. The Marble Institute of America recommends that when natural stone is installed in public facilities that come under ADA jurisdiction, consideration be given to stone with a textured surface or with an ASTM C-1028 test result of 0.5 or higher, especially in high traffic areas. In addition, there are slip resistant topical coatings that may be used on stone surfaces. Check the manufacturers SCOF test results and be sure the product was tested on natural stone. Tests using the James Machine (ASTM D-2047) will generally provide the most reliable SCOF results for floor chemicals. Above all, specify floor maintenance procedures and take precautionary measures to minimize the risk of slip/fall accidents. There are several procedures that building owners, cleaning companies and others can take to minimize the risk of slip/fall accidents. The following suggestions are not intended to replace legal counsel if an accident occurs. 1. Pay attention to areas where water and/or spills occur. Walk-off mats should be placed inside the entrance of doors before and during wet and inclement weather. Spilled food and drinks can create slippery conditions on the floor and any spills should be cleaned up as soon as they occur. 2. If the floor is maintained by stripping and waxing, this procedure should be done at night or when there is minimal traffic. Daily wet mopping should also be performed at night or during off hours. 3. Always place wet floor signs in all areas where floor cleaning personnel are working, regardless of the time of day or night. Floor cleaning personnel should warn people who may walk across the floor that it might be slippery. 4. Keep accurate records on the maintenance of floor surfaces. Include in your records the name brands of all products used on the floor, specific procedures that are performed on the floor and how often, and who performed these procedures. 5. Keep a daily log of maintenance procedures. Designate one individual to keep track of the log, perform routine inspections of the floor, and record findings during inspections.
Article courtesy of The
Marble Institute of America
Decorating Studio, LLC or www.DecoratingStudio.com is not affiliated with the authors nor responsible for the actions or content of the articles, or any 3rd party information within or linked to or from Decorating Studio or Decorating Studio's website.
www.DecoratingStudio.com Home Page
"Decorating Studio tops the list of popular home decorating, interior design, chainette fringe, event and wedding decorations & home improvement sites because you always come first! We have Home decor, rhinestone trim, home decorating tips for events, receptions and weddings, home decorating guides, home decorating ideas and home furniture and decor. Do you want to be a decorator or interior designer? We have a complete list of Interior design and decorating schools, colleges and universities by state."